Residence Time and Temperature CFD Study for Incinerators
By Engaged Expert
Tom ElsonMeet our Digital Engineering expert Tom Elson and learn more about his expertise in CFD which enhances our projects with innovative solutions.
BACKGROUND
Incinerators play a crucial role in various industries, including power generation, cement production, animal waste management, general waste management, and cremation services. All these applications are subject to the environmental requirements outlined in the . Article 50, Clause 2 of this directive states:
"Plant shall be designed, equipped, built and operated in such a way that the gas resulting from the incineration of waste is raised, after the last injection of combustion air, in a controlled and homogeneous fashion and even under the most unfavourable conditions, to a temperature of at least 850 °C for at least two seconds."
If hazardous waste (defined as waste with more than 1% halogenated organic substances) is incinerated, the minimum temperature requirement increases to 1100 °C. Our clients approached us to perform detailed Computational Fluid Dynamics (CFD) studies to ensure their plants operate within these standards. Where requirements were not met, we provided recommendations to achieve compliance.
THE CHALLENGE
ÌìÃÀ´«Ã½ Digital Engineering developed a full 3D model of our client's asset, including the kiln (primary combustion zone), the secondary combustion zone, and regions of the post-combustion zone where residence time and temperature are measured in practice. Traditionally, the client used coal as fuel. In an effort to reduce environmental impact, a range of cleaner alternative fuels was considered.
Using the chemical composition of these fuels, we calculated flame temperatures and determined the percentage split of the flue gas for each fuel. Additional calculations regarding material porosity were conducted in regions where the post-combustion flue gas would pass through loose material used in the cement production process.
A passive scalar was set up as a non-invasive method to measure the time the flue gas spends in regions where residence time is measured in practice. Measurement points were established as planes in the model, averaging values to reflect multiple physical measurement points and produce realistic CFD modelling results.
The analysis revealed that for two out of the three fuels considered, the average residence time exceeded two seconds, and the minimum temperature at the second measurement region was above 850 °C. It was concluded that residence time is sensitive to the inlet temperature, which affects the density and, consequently, the flow velocity. The initial mass flow rate at the inlet also impacts residence time, requiring a delicate balance between these factors for an optimal solution.
THE SOLUTION
The refractory lining was identified as a key factor in heat losses within the post-combustion region. To retain heat and maintain the necessary temperature to meet directive requirements, the thermal conductivity of the refractory lining must be appropriately low, minimizing overall heat rejection (quantified by the Heat Transfer Coefficient in the model).
For the case that initially failed to meet the requirements, we suggested adjustments in the mass flow rate of secondary airflow to compensate for the low residence time. Although these adjustments resulted in a decrease in fluid temperature, the residence time increased to exceed two seconds while maintaining the fluid temperature above 850 °C. This enabled our client to present these findings to the environmental agency as evidence that their plant now operates within the IED directive requirements.
Find related Resources
Further Reading
High-Fidelity CFD Modeling case study
Our client needed to understand the operational methane destruction efficiency of their flare under a range of conditions.
Residence Time case study
Our Residence Time case study explores ÌìÃÀ´«Ã½'s commitment to achieving UK legislation.
Case Studies
ÌìÃÀ´«Ã½ Digital Engineering utilize modeling, simulation, data science, and other digital solutions to help our customers solve complex problems.
Digital Engineering Articles, White Papers and Technical Bulletins
Discover our thought leadership written by Digital Engineering experts from different fields, exploring a range of complex subjects related to Digital Engineering.
Related Services
Computational Fluid Dynamics (CFD)
We use Computational Fluid Dynamics (CFD) to simulate and analyze complex problems involving fluid-fluid, fluid-solid, and fluid-gas interactions.
Modeling and Simulation
ÌìÃÀ´«Ã½ Digital Engineering’s modeling and simulation teams are based in four offices worldwide. Whether developing a new capability, solving a new challenge or needing support to existing capabilities, contact us to discuss how we can support you.